Recensione Epetite DNA60 Box Mod




“La Lost Vape EPetite DNA60 TC nasce dall’unione tra la piattaforma EPetite e l’ultimissimo chipset Evolv DNA 60 alimentato da una batteria 18650 (non inclusa). Design originale creato dal leader delle box di lusso, alluminio di alta qualità con una forma rettangolare unica e cover laterali uniche ed in materiali di lussuosi. L’utilizzo di una singola batteria 18650 (non inclusa) ha permesso di mantenere dimensioni ridotte, internamente la box ha un look pulito e rifinito. Il chipset DNA 60 può erogare una potenza fino a 60W con un’efficenza dell’85%, sono incluse tutte le diverse modalità di erogazione normalmente presenti sui chipset DNA, tra cui la modalità TC completamente customizzabile tramite l’utilizzo del software Escribe. Il display da 0.91 pollici è stato posizionato centralmente e mostra tutte le informazioni essnziali in sinergia con i tre tasti di controllo ed il grande tasto di accensione.”


Caratteristiche:

  • Dimensioni: 73mm by 45mm by 27mm
  • Singola Batteria 18650 Ad Alto Scarico – Non inclusa
  • Potenza in uscita: 1-60W
  • Tensione in uscita: 0.2-9V
  • Resistenze in kanthal supportate a partire da 0.25ohm
  • Resistenze per controllo di temperatura supportate a paritre da 0.15ohm
  • Temperature supportate: 200-600F
  • Materiali supportati in TC Ni200 Nickel, Titanium ed Acciaio
  • Intuitivo display OLED da 0.91 pollici
  • Design rettangolare
  • Cover batteria in materiali di lusso: Legno, fibra di carbonio
  • Tasti di regolazione responsivi
  • Tasto di accensione di grandi dimensioni
  • Chipset Evov DNA 60
  • Aggiornabile tramitre Software Escribe
  • 85% di efficenza energetica
  • Funzione di Pre-riscaldamento della coil
  • Protezione da inversione di polarità
  • Protezione Atomizzatore
  • Protezione da bassa resistenza
  • Protezione da corto circuiti
  • Protezione da surriscaldamento
  • Protezione da bassa tensione
  • Porta Micro USB – Aggiornament Firmware
  • Connettore 510

Prestazioni: 10/10
Durata Batteria: 9/10 Il DNA60 gestisce molto bene le 18650
Erogazione:10/10
Qualità: 4/10 Aggiornamento: 20/09/2018
Affidabilità: 7/10
Prezzo: 5/10 (prezzo dai 90 ai 120 euro)
Portabilità: 9/10 (perfetta)


Dopo ben 3 anni di utilizzo , ho deciso di sostituire la mia amata Epetite 40W (ancora perfettamente funzionante) con la sorella maggiore, col recente (ma non così tanto) circuito DNA60 utilizzabile ottimamente col controllo temperatura [TC].
Partiamo dalla resistenza interna della box. Il produttore indica circa 0,006 Ohm, le mie misurazione la ritengono ben superiore, circa 0,0012/0,0015 UNA FOLLIA PER IL TC Ohm. Quindi se volete utilizzarla col TC vi consiglio di mandare l’atom in corto, o compratevi un “cazzillo” per capire effettivamente quale è la resistenza interna. Edit: per il tc vi consiglio di virare su box con resistenza interna minore es. sbody macro dna 75
-La box è costruita molto bene, con materiali di ottima fattura. Gradevole esteticamente e molto leggera.
-Un difetto è dato dagli sportelli piuttosto ballerini ,ma col tempo ci si abitua.
-Eroga in maniera ottimale il wattaggio selezionato, analizza correttamente la resistenza degli atomizzatori , ed non ha impuntamenti o problematiche varie. — –Ottima anche la solidità dei tasti e la bellezza del BIG display.
-Molto semplice il cambio batteria, anche se era molto più veloce quello della sorella precedente (DNA40).

Utilizzare tutte le funzioni del menù del DNA60:
Modes
Locked mode: Pressing the fire button five times with less than .7 seconds between presses will cause
the device to enter Locked mode. In Locked mode, the device will not fire and the output power will not
adjust accidentally. While in Locked mode, the screen will be off, except that pressing a button will show
“Locked, Click 5X”. To exit Locked mode, press the fire button 5 times.
Stealth mode: While locked, holding the fire and down buttons simultaneously for five seconds will
switch to stealth mode. In this mode the display is off. It will still show error and lock messages. To
switch back to normal display mode, hold down the fire and down buttons simultaneously for 5 seconds.
This setting is stored to internal flash memory, and remains if power is removed.
Power Locked mode: Holding down both the up and down buttons for two seconds will place the device
in Power Locked mode. In this mode, the mod will operate normally, but you will not be able to change
the power setting. This mode prevents accidental power level changes due to the buttons being pressed
while in a pocket. To exit Power Locked mode, hold the up and down buttons for two seconds.
Resistance lock: The DNA 60 relies on the cold resistance of the atomizer to measure temperature
accurately. If the connection is not stable or if you find the measured resistance drifts with time, it may
be desirable to lock the atomizer resistance. To do so, while locked hold both the Fire and Up buttons
for two seconds to enter Resistance Lock mode. In this mode, the DNA 60 will use the present atomizer
cold resistance without refinement until the atomizer is disconnected or the resistance lock is disabled.
A lock symbol will replace the ohm symbol on the display. To disable resistance lock, repeat the
procedure to lock it.
Max Temperature Adjust: From Locked Mode, holding down both the up and down buttons for two
seconds will place the device in Max Temperature Adjust mode. Once this mode is entered, the max
temperature will be displayed. The up and down buttons are used to adjust the max temperature. To
save the new temperature setting and exit, press the Fire button.
Profiles
The DNA 60 allows you to save and select between eight groups of output settings. Each group of output
settings is called a Profile. To switch between profiles, put the DNA 60 into Power Locked mode by
pressing and holding both the up and down buttons simultaneously for two seconds. From power locked
mode, to cycle between profiles, double click the Up or Down button. To select the displayed profile,
press the fire button.
The coil material for each Profile can be changed directly on the device for any material that exists in the
Materials Repository. To change the currently selected Profile’s material, press the Fire button five times
to Lock the device. With the device Locked, hold the Up, Down, and Fire buttons simultaneously for two
seconds. Then, use the Up and Down buttons to cycle through materials, when the desired material is
displayed press the Fire button to confirm your selection.
Evolv recommends setting up one profile for each atomizer that you regularly use with the DNA 60. It is
much faster to switch profiles than it is to set up the settings for the atomizer again.
Coil Materials
Each profile contains an output power setting and a maximum temperature setting. These can be
adjusted on the device, and will be saved when a different profile is selected. Additionally, the
resistance lock setting and value for each atomizer is saved in the profile, which can alleviate
temperature inaccuracies stemming from attaching atomizers before they have completely cooled.
Many more output settings, including the coil material and preheat settings can be adjusted on a perprofile
basis using the Escribe PC software.

 

“La promuovo a pieni voti, anche perchè è una delle poche box-mod di piccole dimensioni per TC.”
EDIT: 20/09/2018. Purtroppo dopo soli due mesi di utilizzo la BOX ha perso tutta la vernice laterale. Non è mai caduta, mai trattata male. Uno schifo considerando quanto l’ho pagata.  Bocciata SICURAMENTE.

Gallery:

 

Condividi La Recensione!